Borrelli Ice Machine 30-120kg User Manual

Ice Machine 30-120kg · IM-30 · IM-50 · IM-80 · IM-120 · Revision 1.0

This manual covers safe installation, day-to-day operation, cleaning and troubleshooting for the Borrelli Ice Machine 30-120kg. Please read it before operating the unit.

1. Warnings and Safety

These precautions ensure safe, correct use of the ice machine and minimise the risk of injury or damage.

• Keep all vents clear while the machine is operating.
• Connect the machine to a potable (drinking quality) water supply only.
• Do not damage the refrigerant circuit.
• Do not use mechanical devices to accelerate defrosting unless recommended by the manufacturer.
• Do not put anything other than water into the machine.
• Never chip or force ice off the evaporator — use the de-icing cycle.
• Disconnect the machine from power before cleaning, maintenance or replacing parts.
• All repairs, disassembly or modification must be performed by a qualified technician.
• Use a dedicated wall outlet; do not use flammable sprays or substances near the machine.
• Dispose of the unit only at an authorised waste centre; do not expose it to a flame.
• After switching off, wait 5 minutes before restarting — restarting too soon can overload the compressor.

↑ Back to contents

2. Installation

Before use

• Remove all packaging and leave the unit to stand upright for 12 hours before switching on, so the refrigerant can settle.
• Clean the interior and the storage bin before first use.
• Discard the first two batches of ice.

Positioning

• Install on a flat, stable surface sturdy enough to support the loaded unit, indoors and out of direct sunlight or heat.
• Keep the machine in a temperature-controlled environment, not exposed to rain or weather.
• Allow 20 mm at the sides and 100 mm at the rear (15 cm back and sides on larger models) for airflow.

Water and drainage

• Connect the labelled water-supply pipe (with its filter) to the corresponding inlet; seal the threads with Teflon tape. If unsure, use a licensed plumber.
• Insert the drainage pipe into the machine and run it to the drainage point. The drain outlet must sit lower than the machine outlet, as it is gravity-fed.
• After connecting, the self-locking drain fitting keeps the connection from leaking.

↑ Back to contents

3. Cleaning

Exterior and interior

• For dust, wipe inside and out with a dry cloth.
• For a deeper clean, use a mild detergent and a soft cloth.
• Clean the unit regularly.
• Never use polishing powder, soap powder, benzine, oil or hot water — these damage the paint and plastic.

After cleaning, check the power cord for cracks or damage. If you find any, contact Borrelli.

↑ Back to contents

4. How to Use

The unit is operated from the control panel on the front. The display shows the ice-making time or a countdown.

Button functions

• ON/OFF – turns the unit on; press again for standby (off).
• Timer / Clean – press to set a timed start or stop; press and hold to begin the cleaning cycle.
• LED / De-Icing – press to turn the interior LED light on and off; press and hold to start a de-icing (harvest) cycle.
• Up (+) and Down (−) – adjust the time shown on the display. Longer time makes thicker ice.

Indicator lights

• Power: the unit is switched on. Ice Full: the sensor flap is held open by ice – the bin is full and the machine pauses.
• Ice Making: a batch of ice is being made. Lack Water: the water supply is low or interrupted – check the inlet and tap.
• Time: a timed start or stop is set. Clean: the cleaning cycle is running.

Setting ice thickness

• Ice thickness depends on the time given to each batch – longer means thicker.
• Use the + and − arrows to set the time. Thicker ice: settings around 6–8; thinner ice: settings around 4–6 (about 15 minutes is the thinnest).
• If cubes come out too thick, set a thinner (shorter) time.

Sensor flap

• The sensor flap tells the unit when to stop making ice; when it is held down by ice, ice-making pauses.
• If ice jams the flap open, remove the ice so it can move freely and production can resume.

↑ Back to contents

5. Tips and Tricks

Follow these tips to get the best performance, efficiency and lifespan from the machine.

Water quality

• Use a potable water supply; a filter improves clarity and reduces scale.
• Flush the machine after any interruption to the water supply.

Condenser

• Clean the condenser regularly to clear dust – a clogged condenser reduces output and shortens the compressor's life.

Long shutdown

• Switch off, drain the water, clean the bin and leave the lid open to air.

↑ Back to contents

6. Specifications

Dimensions in mm; cube 22 × 22 × 22 mm; 304 brushed stainless steel. From borrelli.com.au. Allow 20 mm at the sides and 100 mm at the rear. Supplied with an installation kit. IM-120 is also sold as the clearance-stock IM-120CL (same specification).

↑ Back to contents

7. Before Requesting Service

Please check the following if you encounter a problem. If it continues after these checks, contact Borrelli.

↑ Back to contents

8. Warranty and Enquiries

Warranty periods vary by product. For the period that applies to your model, see its product page. For the warranty terms and how to make a claim, see our Terms & Conditions. Keep your proof of purchase, as it may be required.

↑ Back to contents

Related manuals

Other Borrelli manuals:

• 1 Door Bar Fridge — BC-130
• 2 Door Bar Fridge — BC-210
• 3 Door Bar Fridge — BC-320
• 1 Door Upright Bar Fridge — BC-310U · BC-400H
• 2 Door Upright Bar Fridge — BC-510U · BC-800H · BC-1000H

See all Borrelli user manuals, or browse the related range.